📏 Digital Rolling Measuring Tool – LCD Display & Precision Material Measurement

$43.98 USD
Limit: 1 item per order
Digital Rolling Measure
Measure Directly On the Material
Rolling-wheel digital gauge with backlit LCD, metric and imperial units, and 1/32 in precision for woodworking and construction.
Digital rolling measuring tool clamped on a saw fence
1/32 in Precision Metric + Imperial Backlit LCD 2 x AA Batteries
At a Glance
 
Roll Along the Surface
A measuring wheel rides the material so you read the distance without stretching a tape across the cut.
Read It at a Glance
The backlit LCD stays legible in dim workshops and bright outdoor job sites.
Switch Units Instantly
Toggle between metric and imperial readings without changing devices.
Clamp On and Cut
Attaches to saw fences, guides, and rails so the readout sits where you are cutting.
Built Around Precision
Numbers that matter at the saw
1/32
INCH INCREMENT
0.5
MM RESOLUTION
6
MEASURE MODES
2
AA BATTERIES
Getting Started
 
Diagram of buttons, display, measuring wheel and setup steps
1
Select Units
Press the unit button to switch between imperial fractions and metric readings.
2
Enter Blade Width
Hold the blade against the fence, then rotate the wheel until the correct blade width shows.
3
Zero the Material
Lightly press the material on the left edge and select the zero button to lock the reference.
4
Slide and Cut
Move the material to the cut location; the display follows the wheel the whole way.
Core Features
 
W
Rolling-Wheel Measurement
The wheel tracks along the material, cutting down repeated manual measuring and marking.
L
Backlit LCD Display
A large screen with clear digits stays readable in low light and outdoors.
U
Dual Measurement Units
Read in feet, inches, and fractions or in millimeters and centimeters.
P
Fine Measurement Precision
Readings down to 1/32 inch, roughly 0.5 mm, for detailed woodworking work.
C
Versatile Cutting Measurements
Handles angles, slopes, rise and run, and compound cuts.
B
Battery Operated
Runs on two AA batteries for cordless use anywhere on the site.
Measurement Functions
 
Linear Measurement
Roll the wheel from edge to edge and read the length directly, in either unit system.
Angle Measurement
Set the tool against the blade or fence to capture the angle at the cut.
Zero Reference
Press zero at your start point so every later reading is measured from that edge.
Rise and Run
Read the two legs of a slope together to plan stairs, rafters, and ramps.
Slope Measurement
Capture pitch angles on roof and drainage work without extra calculations.
Compound Cut
Supports combined bevel and miter setups on molding and trim.
Wide Compatibility
Clamps to common saw fences and guides
Tool mounted on a cut off saw and miter saw
1
Cut Off Saws
Fits the fence so the stop position reads on screen instead of on a tape.
2
Miter Saws
Handle angled trim work with the readout sitting at eye level on the table.
3
Band Saws
Keep the measurement reference fixed while the workpiece feeds through.
Safer Reading, Closer to the Cut
Centralized measurement keeps your hands out of the blade path
Digital measure on a circular saw table with hands clear of the blade
A
Read Without Leaning In
The screen faces the operator, so you check the number without bending toward the blade.
B
Hands Stay Back
Measure once at the fence and keep fingers clear during the feed.
C
One Reference, No Guessing
The zero point holds through the cut, removing second measurements mid operation.
Works on Any Flat Material
Wood, pipe, metal, and trim
Four panel view measuring wood, pipe, metal, and trim
01
Wood and Lumber
02
Pipe and Tube
03
Metal Stock
04
Trim and Molding
Specifications
 
Product Type
Digital Rolling Measuring Tool
Display
Backlit LCD
Measurement Units
Metric and Imperial
Measurement Precision
Up to 1/32 in (0.5 mm)
Functions
Linear, Angle, Slope, Rise and Run, Compound Cut
Power Source
2 x AA Batteries
Batteries Included
No
Main Material
Polymer
Design
Handheld Rolling-Wheel
Best For
Woodworking, Construction, Cabinetmaking
Customer Reviews
 
4.7
 
 
 
 
 
Based on 1,200 reviews
5950
 
4175
 
345
 
218
 
112
 
Mark T.1 week ago
 
 
 
 
 
Put it on my miter saw fence and stopped using a tape for trim altogether. Setting zero once and watching the number move is faster and my cuts line up first try.
Priya S.3 weeks ago
 
 
 
 
 
The fractional readout is what sold me. I work in inches mostly but the mm option is handy for hardware spacing. Only wish it came with batteries.
Luis G.1 month ago
 
 
 
 
 
Been using it on pipe and metal stock too, not just wood. Screen is bright enough in the shop and the clamping arm holds solid while the material slides.
Frequently Asked
 
No. The tool runs on two AA batteries, which are not included, so have a pair ready before first use.
Readings go down to 1/32 inch, about 0.5 mm, which is fine enough for cabinetry and detailed trim work.
Yes. A dedicated unit button toggles between imperial fractions and metric readings at any time.
The clamp arm attaches to the fences commonly found on cut off saws, miter saws, and band saws, and works on flat material such as wood, pipe, metal, and trim.
It compensates for the material removed by the saw blade. Enter your blade width once so the displayed stop position matches the finished cut.
In the Box
 
ITEM 01
Digital Rolling Measuring Tool
ITEM 02
Storage Box
BACK TO TOP
Digital Rolling Measuring Tool
Measure once, cut right.

Jūsų vežimėlis

Įkrovimas