🛠️ Heavy-Duty Construction Lifting Jack – 340 lbs Capacity, Precision Height Adjustment

$43.98 USD
Limit: 1 item per order
340 LBS OF CONTROLLED LIFT
Hold it steady.
Then lift it level.
A one-person construction jack for cabinets, doors, flooring and shelving, so both of your hands stay free for the work that matters.
Manual construction lifting jack with slim tapered base
340
LBS CAPACITY
222
MM MAX LIFT
2
LIFT METHODS
1
PERSON SETUP
IS IT FOR YOU
Built for solo installs.
Read this before you buy, so there are no surprises on site.
+
Installing cabinets, panels or doors when nobody is around to hold them
+
Leveling flooring, shelving or trim while you keep both hands on the tool
+
Tight under-cabinet and toe-kick spaces where a normal jack will not fit
-
Full-size appliances, vehicle work or anything above 340 lbs
-
Continuous production lifting, where a powered lift is faster
THE NUMBERS
340 lbs. 8-3/4 inches.
Enough capacity for a loaded cabinet, a solid-core door, or a stack of flooring, with height to spare under most overhangs.
340
LBS
Maximum lifting capacity
154
KG
Same limit, metric
8-3/4
IN
Maximum lifting height
222
MM
Same height, metric
CAPACITY
Why 340 lbs matters
A standard base cabinet with countertop runs well under this limit, so the jack holds the load without you holding the jack.
HEIGHT
Why 8-3/4 inches matters
That is enough travel to seat a cabinet on a floor that is not flat, or to lift a door panel clear of its frame before setting it down.
TWO METHODS
Squeeze it, or step on it.
The reinforced handle works two ways. Pick whichever keeps your hands where you need them.
Foot step hands-free lifting on the reinforced handle
 
Grip and squeeze the overmolded handle to raise the platform in small increments.
 
Best for fine adjustment when you are setting a cabinet edge or nudging a door into line.
 
Metal reinforced so the handle does not flex when you load it up.
 
Step down on the reinforced handle with your boot to raise the load hands-free.
 
Both hands stay free to guide the panel, hold the drill, or check the level.
 
Best for heavier lifts where leg pressure is easier than grip pressure.
SETTING IT DOWN
Lowering is the careful part.
Raising is easy. The precision lowering tab is what lets you bring a panel down by millimetres instead of dropping it.
No-load quick release button for setting the tool under a panel
 
Precision lowering tab releases height gradually, so you can stop at the exact point you need.
 
No-load quick release resets the jack fast when the load is off, ready for the next position.
 
No sudden drops under load, which is the difference between a seated cabinet and a cracked one.
KNOW YOUR JACK
Every part has a job.
Annotated diagram of the jack parts and load rating
1
Reinforced handle
Overmolded grip with metal reinforcement, for hand squeeze or foot step
2
Precision lowering tab
Gradual release for fine height adjustment under load
3
No-load quick release
Resets the platform fast when nothing is resting on it
4
Slim tapered base
Slides under low-clearance material such as a cabinet toe kick
5
Flush mount anchor points
Bolt the base to a surface when you need it to stay put
6
Metal rail and platform
Carries the load straight up, with no sideways drift
IN USE
Set. Lift. Work.
The jack holds the weight while you drill, shim, or screw. That is the whole point.
Jack holding a panel while the worker drills it
1
Slide the base under
The tapered base slips beneath the panel, board or cabinet edge with room to spare.
2
Raise it to height
Squeeze the handle or step on it until the load sits exactly where the plans say.
3
Work with both hands
Drill, screw, shim and level while the jack carries the material for you.
WHERE IT EARNS ITS PLACE
Four jobs it saves.
Worker stepping on the jack to raise a wall panel
CABINETS
Base cabinet install
Hold a cabinet at counter height while you shim the base and drive the screws. No second pair of hands needed.
DOORS
Door and window positioning
Lift a door panel into the frame and hold it there while you set the hinges and check the swing.
FLOORS
Flooring and leveling
Press laminate, tile or board into place and hold it while the adhesive sets.
SHELVES
Shelving and trim
Support a shelf run or a trim board at the height you want before fixing it.
THE SLIM BASE
It fits where a jack should not.
The tapered forged base slides into gaps that stay out of reach of a normal lifting tool, like the space under a cabinet toe kick or a door sill.
Jack sliding under a low clearance wall baseboard
 
Low profile entry slides under sills, toe kicks and stacked boards.
 
Wide footing spreads the load so the jack does not tip when you push it sideways.
 
Anchor points let you lock the base down for repeat lifts in one spot.
THE DETAILS
Specifications.
Product type
Manual construction lifting jack
Max capacity
340 lbs / 154 kg
Max lift height
8-3/4 in / 222 mm
Operation
Hand squeeze / foot step
Lowering
Precision-controlled lowering tab
Base
Slim tapered base with anchor points
Material
Metal with reinforced handle
Power required
None, fully manual
Best for
Cabinets, doors, flooring, shelving, remodeling
WHAT OTHERS SAY
Reviews.
4.6
 
 
 
 
 
Based on 132 verified reviews
5 stars
 
95
4 stars
 
26
3 stars
 
8
2 stars
 
2
1 star
 
1
DM
Derek M.
October 18, 2026
 
 
 
 
 
I install base cabinets alone most days and this replaced a block of wood plus a lot of swearing. Set it under the cabinet, step on it, and it stays where you put it. The lowering tab is the part I did not know I needed.
PS
Priya S.
October 6, 2026
 
 
 
 
 
Used it to hold a door panel while I set three hinges by myself. Honestly it saved me calling a neighbour. The base is thin enough that it slid right under the sill without lifting the panel first.
TR
Tom R.
September 30, 2026
 
 
 
 
 
Works as described, but the travel is shorter than I expected in practice. On an uneven subfloor I ran out of height before the cabinet was level and had to shim the rest. Good tool, just plan for the 8-3/4 inches.
OFFICIAL RESPONSE
Thanks for the honest note, Tom. The 8-3/4 inch travel is the full rated lift, so on a floor with more than that in variance the base still needs shimming first. We are adding a clearance guide to the listing so buyers can check their gap before ordering.
LK
Lina K.
September 21, 2026
 
 
 
 
 
Bought it for a bathroom remodel and ended up using it far more than the tile spacers. It holds a board steady while you check level, which is the fiddly part. One star off only because I wish the handle were a little longer for bigger boots.
MB
Marcus B.
September 9, 2026
 
 
 
 
 
No batteries, no hoses, no charging. I keep it in the van and it just works. Lifted a solid door on my own without asking anyone for help, which is the whole reason I bought it.
QUESTIONS
Frequently asked.
Can it lift more than 340 lbs?
No. 340 lbs (154 kg) is the rated maximum and it should not be exceeded, even briefly. For heavier loads use a rated floor jack or a team lift.
Does it need power or batteries?
No. It is fully manual: hand squeeze on the reinforced handle, or foot pressure for hands-free lifting. There is nothing to charge.
Will the base fit under a cabinet toe kick?
The base is slim and tapered specifically so it can slide under low-clearance material. Check the gap against the base profile before ordering if your clearance is very tight.
How do I lower it slowly?
Use the precision lowering tab to release height gradually while the load is on the jack. The no-load quick release is only for resetting the platform when nothing is resting on it.
Can one person use it safely?
Yes, that is the design intent. Foot-step operation frees both hands for aligning the panel. Keep the load within the rated capacity and stay off the rail itself.
What surfaces does it work on?
Drywall, wood, laminate, tile and concrete. On very uneven subfloors, shim the base first so the jack has a level footing.
WHAT ARRIVES
One tool. Nothing else needed.
No charger, no battery, no accessories you will never use.
1
Construction lifting jack, with reinforced handle and tapered base
 
Works out of the box. No assembly and no setup step before your first lift.
 
Keep it in the van. Manual operation means nothing to maintain between jobs.
Back to top
A steadier way to lift

Váš Košík